How to create fake ice cubes for tops of Tumblers with UV Resin

by TERS Team June 26, 2022

Want to know How to Create the Fake Ice Cube look on the Top of Custom Tumblers?

A Quick Video Demo is located below this article.

We created this quick article describing how, following a video by our friend at Kelsey's Korner. You can find more info and creations by her here @kelseys_korner_ . Additional thanks to @createstudios_diy for hosting the "Makers Gonna Make" event.

Before we get started, let's gather supplies.

We will need:

  • UV Resin
  • UV Light - Recommended having large lamp & UV pen
  • Tumbler Top
  • Stones/Ice Cubes (acrylic or epoxy resin based)
  • Simulated Fruit (acrylic or epoxy resin based)

Step 1.

Seal the tumbler cup top with UV Resin . IF the tumbler top has a seal that opens and slides back to close, we want to seal it in the closed position and fill any gaps underneath the slide with the UV Resin. (The lid can be sealed open or with a gap for a straw too, just be sure to fill any gaps that mildew may build up in).

***The goal is to prevent any unwanted buildup underneath the design we are about to create.

To do this simply, apply enough UV Resin to fill the crevice then secure the lid from sliding back open. Be sure you are securing the lid in the closed position. The owner would likely not be able to drink from the top with the design on it. This is why permanently closing the lid is most ideal in this scenario.

Apply UV light to the area for 1-3 minutes. It will cure both clear and rock hard.

Step 2.

Now that the gaps are filled, cured, and dry to touch, we are going to apply a moderate coating of UV Resin to the top again. We will apply the coating where we will place the stones to simulate the ice cube base.

***This time we are going to place the stones onto the uncured UV Resin. Be sure the stones are in contact with enough of the UV Resin coating to adhere to the top once we apply UV light.

Step 3.

We can also build with simulated acrylic or epoxy resin fruit decor, glitter, sequence etc. to complete the design. Just be sure each piece is secured with UV Resin.

The UV pen becomes very handy when handling smaller decor. Just apply a small amount of UV Resin to the item and secure it with the UV pen light.

Step 4.

Once we have the desired look with the stones and simulated fruit, we can place the entire lid under a larger UV light to cure the entire project. Again allow 1-3 minutes for the cure.

Step 5.

Now just make sure all the items are secured to the lid. If any items are loose, apply a small amount of UV Resin and cure it with the UV light again.

Hope this was helpful.

Here's the quick demo video by Kelsey's Korner. You can view it on either our Youtube channel or Instagram feed.


Let us know what you would like to create below in the comments.

**If you made it this far down, We occasionally pick the best comment to win a giveaway. -hint-hint

We created a handy comparison guide to help understand the different properties of our epoxy resin. Just follow this link here https://www.theepoxyresinstore.com/blogs/news/what-epoxy-resin-is-best-for-my-project

https://www.theepoxyresinstore.com/ is an expert manufacturer of various epoxy resins that can be used for both craft projects and industrial applications. We also offer colors, pigments, glitter, and other additives for various epoxy resin projects.

The Epoxy Resin Store
support@theepoxyresinstore.com
Phone: (951) 677-0400
Address: 540 Crane St suite A Lake Elsinore, CA 92530
https://www.theepoxyresinstore.com


Social Accounts:
https://www.facebook.com/TheEpoxyResinStore
https://twitter.com/epoxyresinstore
https://www.linkedin.com/company/the-epoxy-resin-store
https://www.youtube.com/channel/UC3NKcCrYL5uHK-sH5XMQ9HA
https://instagram.com/theepoxyresinstore

Back to The Epoxy Resin Store blog, Tips & Tutorials
Go to full site